Nexus Ascend is a rechargeable prostate massager with a shaft that rotates while moving up and down. Its five modes combine the two motions to create a different experience from a conventional stationary vibrator. This exact Stag Standard listing is SKU 97848.
Published specifications
- Motion: simultaneous shaft rotation and vertical movement.
- Modes: five.
- Maximum shaft diameter: 36 mm / approximately 1.42 inches.
- Published insertable length: 100–120 mm / approximately 3.94–4.72 inches.
- Material: smooth body-safe silicone.
- Water protection: IPX6 splashproof.
- Power: rechargeable.
- Maker-stated charge time: 2.5 hours.
- Maker-stated operating time: approximately one hour.
The insertable-length range reflects a moving mechanism, not an instruction to force the device to its maximum depth. Confirm comfort with the motor off and allow clearance for the full vertical stroke before selecting a mode. The rigid mechanism under the silicone does not flex like a manual soft toy.
What dual-action movement means
Ascend’s shaft rotates and changes vertical position during the same operating cycle. Rotation changes which part of the curved surface applies pressure, while the vertical stroke changes depth. Five modes alter the motion pattern or intensity. Because both movements occur together, a small change in angle or body position can meaningfully change sensation.
For separate thrusting and perineum vibration, compare the Nexus Thrust Prostate Edition. For rotating motion with remote control, see the Nexus Revo Intense or Nexus Revo Extreme. For a smaller nonpowered profile, compare the Aneros PSY.
Set up before insertion
- Charge the device fully enough to test every mode outside the body.
- Inspect the silicone, moving shaft, base, control, and charging area for tears, gaps, swelling, or exposed components.
- Place the product on a clean surface and watch the complete motion path so you understand its maximum travel.
- Apply generous water-based lubricant to the shaft and body opening, keeping the control and charging area dry.
- Insert only with the motor off. Position the base so it remains reachable and the shaft has room to move.
- Start the lowest comfortable mode and stop immediately if the mechanism stalls or the motion creates sharp pressure.
Do not sit, kneel, or roll onto a moving internal product. Do not hold the shaft stationary while its motor tries to rotate or thrust. Avoid positions that trap the base or make withdrawal dependent on the motor. If the device stops unexpectedly, switch it off and remove it slowly rather than repeatedly restarting it inside the body.
Fit and sensation checks
The 36 mm maximum diameter is a starting measurement, but movement can make the shaft feel fuller than a stationary product of the same width. Begin slowly and reassess after every mode change. Stop for pain, bleeding, numbness, unexpected resistance, loss of sensation, motor heat, or difficulty removing the device. Do not use numbing products to hide discomfort.
Ascend is not a medical device and does not diagnose, prevent, or treat prostate or pelvic conditions. Anyone with recent surgery, unexplained pain or bleeding, impaired sensation, or another relevant health concern should obtain appropriate clinical guidance before internal use.
Charging and IPX6 care
IPX6 indicates protection from powerful water jets under test conditions; it is not an immersion rating. Do not submerge Ascend, leave it in standing water, or treat it as bathtub-safe. Follow the received instructions for cleaning around the moving junction and charging area. A damaged seam or seal ends any reliance on the water-resistance rating.
Charge for the maker-stated 2.5 hours only with the supplied equipment and an allowed power source. Use a dry, stable, ventilated surface away from bedding, heat, direct sun, sinks, and tubs. Do not charge while wet. Stop using the product if it becomes unusually hot, swollen, cracked, leaking, or odorous.
Cleaning and storage
Switch the device off and disconnect charging. Clean the silicone with warm water and mild unscented soap or a compatible cleaner, keeping within the IPX6 boundary. Work gently around the shaft junction without pulling, twisting, or forcing the mechanism by hand. Do not boil, bleach, dishwasher-clean, scrub with abrasives, or use alcohol or solvents unless Nexus expressly permits the method.
Rinse without immersion, blot the exterior, and let every seam and charging contact air-dry completely. Store Ascend with the shaft in its neutral position, free from pressure or sharp bends, and keep its charger protected from moisture.
Browse prostate toys, review materials and care and our cleaning guide, read the hygiene-sensitive return policy, or return to the full shop.